How To Use Acoustic Foam

Download Article

Sound waves bounce off surfaces and tin interfere with your ability to record music. Luckily, acoustic panels can minimize this and make a room less echoey. To hang acoustic cream, y'all'll want to find the optimal area on the wall to place the panels. Then, y'all'll have measurements and adhere them to the wall with Command strips. If you follow the proper steps, yous can finer install audio-visual foam without damaging the wall that y'all're applying it to.

i
Install the audio-visual foam behind your recording equipment. Audio bouncing off the walls can affect your recordings and create unwanted effects. If you create music at a mixer or desk, consider putting audio-visual cream behind information technology. Roofing an entire wall will significantly reduce sound reflection, nonetheless, you only need a single panel to notice a difference when you lot record.^[i]
- Position the foam so that it's in betwixt both of your studio monitors or speakers.
- Audio-visual foam volition not soundproof a room.
- Acoustic foam should be centered on the wall and at ear level.
two

Install cream on the walls on walls opposite of your speakers. Installing foam on the wall across from your speakers will minimize how much sound bounces back into your recording device. Place panels in areas directly across from speakers to minimize how much the sound bounces. Y'all only need a single panel for this, nonetheless larger coverage will further reduce the sound reverberations.^[ii]

Advertisement
3
Wipe down your walls with rubbing alcohol. Use a clean rag or cloth saturated in rubbing alcohol to remove dirt from the walls that you want the foam to become on. Cleaning the walls before installing the acoustic cream volition help the foam stick.^[three]
- Practice not apply regular household cleaners because it tin can reduce the adhesion of the foam.
4
Measure out the foam panels and the wall where you're installing them. Lay the cream panels on a apartment surface side by side and use a tape measure to record their full length and width and record information technology on a piece of paper. Then, take your measurements and mark out the area on the wall where you want to install them. This volition give you an thought of how much space they volition take up.^[iv]
- Small-scale recording studios may only need a unmarried foam console backside the mixer.
- If you don't have plenty room on your wall, utilize fewer foam panels.
five

Use an electric etching knife to cut the cream panels if they don't fit. Cutting the foam with an electric knife will requite it a clean edge. Concur the panel on its sparse terminate and use a carving knife to cut down through the acoustic foam. Advisedly movement the carving knife down the console to cut information technology to size.^[5]
6
Draw an outline of the foam panels on the wall. Draw an X in each corner of the installation site according to your measurements. Line a level against each corner of the installation area and depict directly lines to create the edges for your cream panels. Doing this in advance will help y'all keep the panels direct equally yous install them.
- If you don't employ a level, your cream panels may be crooked.

1
Spray the backside of the cream pieces with adhesive spray. Purchase an adhesive spray online or at an arts and crafts store. Lay the audio-visual panels on the floor, bumpy side downwardly. Spray the back of the panels in a dorsum and forth movement, just leave the edges of the cream unsprayed to make it easier to cut later.^[vi]
- If you have foam panels that came with adhesive on the dorsum, you can skip this stride.
- You can purchase adhesive spray online or at an arts and crafts store.
2
Press the cream against a piece of paper-thin, agglutinative side downwardly. Gluing cardboard to the back of the cream will go far easier for the Command strips to stick to the panels. Printing and concord the foam against the cardboard for 30 seconds.^[7]
- Using cardboard will brand your acoustic foam reusable and will preclude damage to your wall.
3
Let the glue dry out. Exit the foam in a well-ventilated surface area for ane or 2 hours, then check to brand certain the foam is dry. The foam should remain firm on the paper-thin and shouldn't shift around when you impact information technology.
- You lot tin can put the foam in front of a window or fan to quicken the drying process.
four
Cut off the excess cardboard effectually the foam. Practice not cut into the foam itself. Position your scissors and cut forth the within edge paper-thin. Information technology's okay if the foam overlaps the cardboard.^[viii]
- No paper-thin should be visible when looking at the bumpy side of the foam panels.
five
Put Command strips on the backside of the panels. Command strips are small rectangles that accept an easily removable adhesive. Remove the paper tab on the Command strips and place 1 in each corner on the backside of the foam panel. Press against the Command strip for 10 seconds to make certain it stays attached to the paper-thin.^[nine]
- The Command strip should be stuck to the cardboard, not to the foam.
6

Press the acoustic foam against the wall. Remove the other paper tab to reveal the adhesive, then carefully line up your acoustic foam panel in the corner of the area that you drew before. Printing the dorsum side of the cream against the wall and hold it for 30 seconds. This should secure information technology in place.^[10]
seven
Finish installing the remaining panels. Proceed repeating the steps to apply a row of acoustic foam on your wall. Continue adding more pieces of the foam until you lot make full the desired space. Once all the pieces take been installed, use an eraser to remove the pencil marks that you created.^[11]
- Alternate the management of the pattern on the acoustic panels for maximum effectiveness and visual entreatment.

Advertizing

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Thanks for submitting a tip for review!

Things Y'all'll Need

Measuring tape
Level
Pencil
Electric carving knife (optional)

Adhesive spray
Acoustic foam
Command strips (iv for each foam panel)

About This Article

Article Summary X

To hang audio-visual foam, start past cleaning and measuring the areas that you lot programme to care for, like the space betwixt your studio monitors and speakers and the wall across from your speakers. Once you lot decide where to hang your foam, wipe downwardly the walls with rubbing alcohol to remove any dirt and help the foam stick. In addition to cleaning, measure the areas where you want to install the foam. When you're ready to hang the foam, spray the behind of the pieces with agglutinative and press them against a slice of cardboard. Let the glue dry completely, which should have ane to 2 hours. And so, put command strips on the backsides of the paper-thin and secure them to the wall. To learn how to cutting your audio-visual foam to size, keep reading!

Did this summary help you?

Cheers to all authors for creating a page that has been read 222,766 times.